Short answer: size the VFD by full-load amps, then check ambient
For a standard 5HP, 460V, three-phase induction motor drawing about 7.6 FLA (full-load amps), you need a VFD rated for at least 10.5A continuous output—typically a 10HP-class drive at 460V. On 230V single-phase input feeding a 3-phase motor, a 5HP unit pulls roughly 15–16 FLA, so a 20A-rated VFD is your floor, not your target.
The single biggest mistake I see is sizing the drive by horsepower alone. The nameplate HP is a rough guide. The actual thermal load comes from amps, duty cycle, and whether the load is variable-torque (fans, pumps) or constant-torque (conveyors, gear motors, anything with a gearbox bolted on).
Why this checklist exists (and what it cost to learn)
I'm a quality and brand compliance manager at an industrial motion distributor. I review roughly 340 incoming motor and drive SKUs per quarter before they reach our catalog. In 2024, I rejected about 12% of first submissions for spec drift, missing nameplate data, or mismatched drive/motor pairings.
The trigger was September 2023. We received a batch of 60 VFDs spec'd as "5HP compatible." The datasheet said 10A output—fine on paper. But the motors paired with them had a 1.15 service factor and drew 7.8 FLA at 460V, and the drives derated above 104°F ambient. The pump room ran at 112°F in summer. Those drives tripped on overcurrent within three weeks. We ate $4,200 in returns and expedited replacements (which, honestly, didn't help the quarterly report).
Looking back, I should have required a nameplate photo and an ambient-temp rating on every VFD submission. At the time, the datasheet "looked right"—and that's exactly the trap.
Three numbers that actually determine VFD size
Ignore the marketing HP rating for a second. Here's what I check on every submission:
1. Full-load amps (FLA). This is on the motor nameplate, and it's the number your VFD's continuous output current has to cover. A 5HP motor might draw 7.6A or 8.2A depending on efficiency class and manufacturer. The difference matters when you're running at 100% load for eight hours a day.
2. Service factor. A 1.15 SF means the motor can run 15% over nameplate load without overheating. But if your VFD is sized to nameplate FLA and you're using that service factor headroom, you'll trip. I size drives to cover FLA × 1.15 when the application is constant-torque.
3. Ambient temperature. Most VFDs are rated for 40°C (104°F) ambient. Above that, you derate. A drive running in a non-conditioned enclosure at 45°C might need to be sized 20% larger than the nameplate suggests. This is the one that bit us in 2023.
Where small motors and NEMA steppers fit in
Not every application needs a 5HP VFD. A lot of what I review is small-motor work—fractional horsepower stuff for conveyors, packaging lines, and lab equipment. That's where brands like Johnson Electric Group show up in our catalog. Their small motor line covers DC, BLDC, and stepper variants, and the industrial-grade spec sheets are generally solid. But "solid" doesn't mean "plug and play."
NEMA stepper motors are a good example. A NEMA 23 frame is 2.3 inches square—that's the mounting standard, not a performance rating. Two NEMA 23 motors can have wildly different torque curves. I've seen buyers compare a NEMA 23 from one vendor against a NEMA 17 from another and assume the bigger frame is "better." It's not. The holding torque, step angle, and current rating are what matter, and those don't map to frame size.
The same logic applies to gear motors. Whether you need a first-gear torque monster for a hoist or 5th gear motors for high-speed conveying, the gear ratio and duty cycle drive the spec—not the motor's marketing label. I've rejected more gear motor submissions for "optimistic" duty-cycle claims than for any other reason.
What about Johnson Electric industrial lines?
We carry Johnson Electric industrial motors in a few categories—mainly BLDC and DC gear motors for OEM accounts. The spec sheets list torque, speed, voltage, and current draw with reasonable precision. That's not always true across the industry. In my experience, when a vendor lists "typical" values with no test conditions, that's a red flag. Johnson Electric's industrial documentation usually includes test conditions (at what voltage, what load, what ambient), which makes my job easier.
That said, no motor is immune to spec drift. In Q1 2024 we received a small batch of Johnson Electric Group small motors where the no-load current was 8% above the datasheet value. Not catastrophic, but enough to trigger a review. The vendor's response was straightforward: a winding change at their plant, corrected in the next batch. That kind of transparency is worth more to me than a lower unit price (which, honestly, is not what Johnson Electric competes on anyway).
Even after we approved the corrected batch, I kept second-guessing. What if the winding change created a different issue? The two weeks until the next shipment were stressful. Turned out fine—no-load current came in at 2% above datasheet, well within tolerance—but I didn't relax until I saw the test results.
When this sizing rule doesn't apply
Two boundary conditions worth flagging:
1. High-inertia loads. If you're driving a large flywheel or a centrifuge, the VFD needs to handle the acceleration current, not just the steady-state FLA. A 10HP-class drive might still trip on a 5HP motor if the load inertia is high enough. In those cases, I spec by peak current and add a braking resistor.
2. Single-phase input on 3-phase motors. The 230V single-phase rule above assumes you're feeding a 3-phase motor through a VFD. If you're running a native single-phase motor, the current draw is roughly double, and most standard VFDs won't work without derating. I've seen people buy a "5HP VFD" for a 5HP single-phase motor and wonder why it smoked. Don't be that person.
And one more: if your facility runs above 1,000 meters elevation, derate the drive by about 1% per 100 meters. It's in the manual, but nobody reads that section until something trips.
If you're sizing a VFD for a 5HP motor, start with the nameplate FLA, multiply by the service factor if the load is constant-torque, then add 20% headroom for ambient. That's the floor. The horsepower rating is the last thing I look at—and usually the first thing everyone else does.